MIMAKI CJV30 Series, Maintenance Manual

Page: 8 / 316

© 2009 MIMAKI ENGINEERING CO.,LTD. Maintenance Manual Contents R.1.2 P.1
Maintenance Manual > Maintenance Manual Contents
Model CJV30/TPC Issued 2008.08.04 Revised 2009.08.27 F/W ver. 2.00 Remark
Maintenance Manual Contents
1.2
Rev.
1 Operating Principle
1.1 Basic Operation
1.1.1 Main Switch Power ON
1.1.2 Sub Switch Power ON
1.1.3 Initial Machine Operation
1.1.4 Detection of a Media Width
1.1.5 Clamp Pressure Switching
1.1.6 Operation for Connecting the Heads
1.1.7 Mark Detection
1.1.8 Main Switch Power OFF
1.2 Maintenance Function
1.2.1 CARRIAGE OUT
1.2.2 WIPER REPLACE
1.2.3 NOZZLE WASH
1.2.4 PUMP TUBE WASH
1.2.5 CR.MAINTENANCE
1.2.6 FILL UP INK
1.2.7 DISCHARGE&WASH
1.2.8 Maintenance Washing Liquid Filling
and Discharge
1.2.9 Waste Ink Tank Warning
1.2.10 Aqua->Sol EXCHG.
1.3 Ink System
1.3.1 Configuration
1.3.2 Ink System Error Monitoring
1.3.3 Supply Cartridge Control and
Selection
1.3.4 Cartridge LED Control
1.3.5 Supply Valve Control
1.3.6 Monitoring of the Amount of
Remaining Ink
1.3.7 Use-up Cleaning
1.3.8 Ink Suction and Discharge Control
1.3.9 Initial Filling
1.3.10 Expiry month and extension of expiry
month for ink
1.3.11 Initial Filling
1.4 Print & Cut
2 Electrical Parts
2.1 Block Diagram
2.1.1 Connection Diagram Inside the Main
Body
2.1.2 Connection Diagram Outside the Main
Body
2.2 Operating Description
2.2.1 Operation Explanation
2.3 Circuit Board Specifications
2.3.1 Power Supply PCB Assy
2.3.2 Main PCB Assy
2.3.3 PRAM PCB Assy
2.3.4 Regenerative Resistivity PCB Assy
2.3.5 Cutter Driver PCB Assy
2.3.6 Station PCB Assy
2.3.7 X-axis Motor Relay PCB Assy
2.3.8 Ink Slider PCB Assy
2.3.9 Cutter Slider PCB Assy
2.3.10 Head Memory PCB Assy
2.3.11 LED PCB Assy
2.3.12 Keyboard PCB Assy
2.3.13 Take-up PCB Assy
3 Workflow
3.1 Ink Related Parts
3.1.1 Replacement of the Head Unit
3.1.2 Replacement of the Cap Assy
3.1.3 Replacement of the Cartridge Assy
3.1.4 Replacement of the Wiper Unit
3.2 Cut Head Carriage
3.2.1 Replacement of the Pen Assy and
LED Pointer
3.2.2 Replacement of the Auto Cutter Assy
3.2.3 Replacement of the Mark Assy
3.3 Driving Parts
3.3.1 Replacement of the X-axis Motor
3.3.2 Replacement of the Y-axis Motor
3.3.3 Replacement of the Y Drive Belt
3.3.4 Replacement of the Linear Encoder
Scale
3.3.5 Replacement the GR Roller Assy
3.4 Electrical Parts
3.4.1 Replacement of the Main PCB Assy
4 Adjustment Items
4.1 Operation Matrix
4.1.1 Matrix of Operations and Adjustments
4.2 Adjustment Function
4.2.1 [HEAD ADJUST] SLANT ADJUST
4.2.2 [HEAD ADJUST] DROP.POS
ADJUST
4.2.3 EDGE ADJUST
4.2.4 MEDIA COMP.2
4.2.5 CAPPING
4.2.6 HEAD ID
4.2.7 HEAD WASH
4.2.8 500mm SQUARE
4.2.9 PEN PRESSURE
4.2.10 LANDING
4.2.11 [PHOTO SENSOR] SENSOR LV.
4.2.12 [PHOTO SENSOR] POSITION
4.2.13 GR/PR POSITION
4.2.14 MOTOR CURRENT