3.
Selecting Speed
Allow the tool to come to a complete stop before
changing speeds. Press the selector button
to
cycle between the settings.
Mode
1
2
3
To
lock
the trigger, push the control switch to the
centre position. The trigger will not work when the
control switch is in the locked position.
Always remove the battery pack before performing
maintenance or changing accessories. Always
lock the trigger or remove the battery pack before
storing the tool and any time the tool is not in use.
driving
screws
self-tapping
RPM 0 - 1700 0 - 3000 0 - 3900
Designed for
IPM 0 - 1400 0 - 3600 0 - 4400
in sheet metal
The
function is designed to reduce screw strip-
ping, screw breakage, and damage to the work sur-
face when driving self-tapping screws. This function
is optimised for the most common materials, including
#8, #10 and #12 self-tapping screws between 1/2"-1"
in length and 18-22 gauge sheet metal.
NOTE:
mode will only run if the trigger is pulled
more than half-way. If pulled less than half-way, the
driver will run in the normal impacting mode. When
using the
once the screw is fully seated.
5
Starting, Stopping and Controlling Speed
These tools may be operated at any speed from 0
to full speed.
1. To
start
the tool, pull the trigger.
NOTE:
released.
2. To
vary
the driving speed, increase or decrease
pressure on the trigger. The further the trigger is
pulled, the greater the speed, up to the maximum
speed set by the speed control.
3. To
stop
the tool, release the trigger and the electric
brake stops the tool instantly.
Impacting Techniques
The longer a bolt, screw, or nut is impacted, the
tighter it will become. To help prevent damaging the
fasteners or workpieces, avoid excessive impact-
ing. Be particularly careful when impacting smaller
fasteners because they require less impacting to
reach optimum torque.
Practice with various fasteners, noting the length of
time required to reach the desired torque. Check the
tightness with a hand-torque wrench. If the fasteners
are too tight, reduce the impacting time. If they are
not tight enough, increase the impacting time.
Oil, dirt, rust or other matter on the threads or under
-
ness.
The torque required to loosen a fastener averages
75% to 80% of the tightening torque, depending on
the condition of the contacting surfaces.
On light gasket jobs, run each fastener down to a
relatively light torque and use a hand torque wrench
WARNING
Maintaining Tool
WARNING
Use only recommended accesso-
ries. Others may be hazardous.
Cleaning
Repairs
For repairs, return the tool, battery pack and charger
to the nearest service centre.
ACCESSORIES
MAINTENANCE
WARNING
To reduce the risk of injury,
always unplug the charger and
remove the battery pack from the charger or
tool before performing any maintenance. Never
disassemble the tool, battery pack or charger.
Contact a
MILWAUKEE
®
service facility for ALL
repairs.
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage
of parts, or any other condition that may affect the
tool operation. Return the tool, battery pack, and
charger to a
MILWAUKEE
®
service facility for repair.
After six months to one year, depending on use,
return the tool, battery pack and charger to a
MILWAUKEE
®
service facility for inspection.
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work
properly, return the tool, charger and battery pack,
to a
MILWAUKEE
®
service facility for repairs.
Clean dust and debris from vents. Keep handles
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain
cleaning agents and solvents are harmful to plastics
and other insulated parts. Some of these include
petrol, turpentine, lacquer thinner, paint thinner,
chlorinated cleaning solvents, ammonia and
household detergents containing ammonia. Never
use flammable or combustible solvents around
tools.
To reduce the risk of personal
injury and damage, never
immerse your tool, battery pack or charger in
liquid or allow a liquid to flow inside them.
For a complete listing of accessories, go online to
milwaukeetool.com.au / milwaukeetool.co.nz or
contact a distributor.
