Milwaukee M12 IR, User Manual

Page: 13 / 16

13
M12 IR (1/4") M12 IR (3/8")
.........................1/4" (6,35 mm) ..............3/8" (9,5 mm)
......................0-250 min -1 ....................0-250 min -1
...........................40 Nm ...........................47 Nm
...........................12 V ..............................12 V
........................0,91 kg ..........................0,91 kg
...........................72 dB (A) ......................72 dB (A)
.......................< 2,5 m/s
2
......................< 2,5 m/s
2
..........................1,5 m/s 2 .........................1,5 m/s 2
TECHNICAL DATA Cordless Industrial Screwdriver
Tool reception ..........................................................................
No-load speed .........................................................................
Torque......................................................................................
Battery voltage.........................................................................
Weight according EPTA-Procedure 01/2003 ...........................
Noise/vibration information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (K = 3 dB(A)) .......................................
The noise level when working can exceed 80 dB (A).
Wear ear protectors!
Total vibration values (vector sum in the three axes)
determined according to EN 60745.
Vibration emission value a
h
:
Impact tightening of fasteners of the maximum capacity of the tool
Uncertainty K = .....................................................................
WARNING! Read all safety warnings and all
instructions, including those given in the accompanying
brochure. Failure to follow the warnings and instructions
may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS
Wear ear protectors. Exposure to noise can cause hearing
loss.
Hold power tool by insulated gripping surfaces, when
performing an operation where the fastener may
contact hidden wiring or its own cord. Fasteners
contacting a live wire may make exposed metal parts of the
power tool live and could give the operator an electric
shock.
Sawdust and splinters must not be removed while the
machine is running.
When working in walls ceiling, or
fl oor, take care to avoid
electric cables and gas or waterpipes.
Do not store the battery pack together with metal objects
(short circuit risk).
Use only System C12 chargers for charging System C12
battery packs. Do not use battery packs from other systems.
Battery acid may leak from damaged batteries under
extreme load or extreme temperatures. In case of contact
with battery acid wash it off immediately with soap and
water. In case of eye contact rinse thoroughly for at least 10
minutes and immediately seek medical attention.
SPECIFIED CONDITIONS OF USE
Do not use this product in any other way as stated for
normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is
in conformity with the following standards or standardized
documents. EN 60745, EN 55014-1, EN 55014-2, in
accordance with the regulations 2006/42/EC, 2004/108/EC
Winnenden, 2011-07-15
Rainer Kumpf
Manager Product Development
Authorized to compile the technical
fi le
BATTERIES
New battery packs reach full loading capacity after 4 - 5
chargings and dischargings. Battery packs which have not
been used for some time should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the
performance of the battery pack. Avoid extended exposure
to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept
clean.
For an optimum life-time, after use, the battery packs have
to be fully charged.
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given
in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration emission may differ. This may signi fi cantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signi fi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
Remove the battery pack before starting any
maintenance
work on the
tool
.
Do not dispose of used battery packs in the household
refuse or by burning them.
Abide by all local authority
re
gulations on the correct disposal of batteries
.
The cordless industrial
ratchet
can be used to tighten
and loosen nuts and bolts wherever no mains connection is
available.