4
• During charging, press the power button to display
the current charge on the fuel gauge.
• USB A Port (for device charging) and DC out port
(for powering heated gear) is shut down when the
Micro-USB port is being used.
•
•
•
A fully discharged battery pack with an internal
temperature in the normal range will charge in about
130 to 525 minutes, depending on the battery pack.
Heavily cycled batteries may take longer to charge
completely.
• After charging is complete, the continuous green
light will come on.
• The charger will keep the battery pack fully charged
if it is left on the charger.
•
The Red Flashing Indicator light on the charger
indicates that the battery pack temperature is out-
side the charging range. Once the battery pack is
within the acceptable range, normal charging will
take place and the red light will be continuous. Hot
or cold batteries may take longer to charge.
the battery pack is fully seated into the bay. Remove
the battery pack and reinsert. If the light continues to
hot or cold, or wet. Allow the battery pack to cool down,
warm up, or dry out and then reinsert. If the problem
persists, contact a
MILWAUKEE
®
service facility.
• If the light indicator does not come on, check that
the battery pack is fully seated into the bay. Remove
the battery pack and reinsert. If the light indicator
still does not come on, remove pack and unplug
charger for at least 2 minutes. After 2 minutes,
plug charger back in and insert pack. If after these
attempts the light indicator still does not come on,
contact a
MILWAUKEE
®
service facility.
Maintenance and Storage
Store your charger in a cool, dry place.
Unplug battery chargers and remove batteries when
not in use. Do not store battery packs in the M12™
Compact Charger and Power Source.
Red: Charging
Green: Charged
Red Flashing: Battery is too hot or too cold
Red/Green Flashing: Damaged or Faulty Battery
•
• Use the Fuel Gauge to determine when to charge
your
MILWAUKEE
®
Li-Ion battery pack.
•
Charging the Battery Pack
When to Charge the Battery Pack
with this MILWAUKEE
®
Charger
Remove the battery pack from the tool for charging
when convenient for you and your job.
MILWAUKEE
®
batteries do not develop a "memory" when charged
after only a partial discharge. It is not necessary to run
down the battery pack before placing it on the charger.
1. Plug your USB A end of the cable into a power
source such as an AC wall adaptor, computer or
car port.
2. Insert the Micro-USB end of the cable into the
Micro-USB port in the charger.
3. Insert the battery pack into charger. The indicator
light will display the charging status:
You can "Top-Off" your battery pack's charge before
starting a big job or long day of use.
The only time it is necessary to charge the
MILWAUKEE
®
Li-Ion battery pack is when the
battery pack has reached the end of its charge. To
signal the end of charge, power to the tool will drop
quickly, allowing you just enough power to finish
making a cut, drilling a hole, or driving a fastener.
Charge the battery pack as needed.
MILWAUKEE
®
LI-ION
CHARGER
CHARGING THE BATTERY
12V Li-Ion Chargers. Other types of batteries
may cause personal injury and damage.
WAR
G
N
I
N
Li-on
Charge only
batteries in
MILW
MIL
AUKEE
W
®
AUKEE
12V
®
To clean the heated jacket:
1. Remove battery pack and battery controller.
2. Push the power cord completely into the battery
controller pocket and zip closed.
3. Machine wash, Gentle Cycle in warm water. Do not
use bleach. Do not dry clean. Do not wring or twist.
4. Tumble Dry on Low Heat. Do not iron.
WARNING
To reduce the risk of personal in-
jury and damage, disconnect and
them.
ACCESSORIES
WARNING
Use only recommended accesso-
Use only
MILWAUKEE
®
accessories and
MILWAUKEE
®
spare parts. Should components
need to be replaced which have not been described,
please contact one of our
MILWAUKEE
®
service
agents. Please visit milwaukeetool.com.au /
milwaukeetool.co.nz or contact our customer
service centre (Australia Toll Free Telephone
Number 1300 645 928) (New Zealand Toll Free
Telephone Number 0800 279 624).
