Adjusting the Side Handle Position
1. Loosen the side handle clamping collar assembly
by unscrewing the side handle grip until the side
handle clamping collar assembly rotates freely.
2.
.
n
o
it
i
s
o
p
d
e
ri
s
e
d
e
h
t
o
t
p
ir
g
e
l
d
n
a
h
e
d
i
s
e
h
t
e
t
a
t
o
R
3. Tighten the side handle grip securely.
Installing/Removing the Bit
Slide the bit through the nozzle and then install
into the tool according to the tool manufacturer's
instructions. For best results, use a bit 177.8mm (7")
in length or shorter.
Fitting the HAMMERVAC™ to the Tool and Bit
For proper suction and depth
Correct
Incorrect
Incorrect
control, position the nozzle as-
the forward face of the nozzle:
1. Press and hold the tool and
bit depth gauge button.
2. Push in the nozzle assembly
front face of the nozzle.
3. Release the tool and bit depth
gauge button.
NOTE:
Fully extend the
HAMMERVAC™ before storing
to preserve spring life.
Setting the Drilling Depth
1. Fit the HAMMERVAC™ to the Tool and Bit.
2. Press and hold the depth gauge button and slide
the depth gauge to the desired depth. The drill-
ing depth is the last visible measurement shown
when viewed from the depth gauge on the top of
the tool. To ensure the HAMMERVAC™ is prop-
erly set to the tool, bit, and desired depth, always
drill a test hole.
OPERATION
WARNING
-
-
mable or combustible materials. Empty dust box
completely before use.
To reduce the risk of injury, always wear proper
eye protection marked to comply with AS/NZS
1337.1. When working in dusty situations, wear
appropriate respiratory protection or use a suit-
able dust extraction solution.
Using the Power Switch
AUTO
To set the HAMMERVAC™ to start auto-
matically as a hole is being drilled, move
.
n
o
it
i
s
o
p
O
T
U
A
e
h
t
o
t
h
c
ti
w
s
r
e
w
o
p
e
h
t
When the nozzle assembly is pushed in,
the HAMMERVAC™ will run.
NOTE:
The
HAMMERVAC™ will continue to run 3-5
seconds after the tool has fully extended to
ensure all dust is captured in dust box.
ON
To turn the tool
ON
, move the power switch
to the ON position. The HAMMERVAC™ will
run continuously.
OFF
To turn the tool
OFF
, move the power switch
to the
OFF
position.
NOTE:
When the HAMMERVAC™ has come to a
of debris that could become lodged.
Proper Operation
1. Empty the dust box.
NOTE:
For optimal use to remove debris in the
dust box, connect a hose to a vaccum and re-
move debris.
2. Install and position the nozzle assembly to the
desired side.
3. Attach side handle clamping collar assembly and
grip to tool.
4. Fit the HAMMERVAC™ to the Tool and Bit.
5. Set the drill depth.
6. Install the battery pack.
7. Turn HAMMERVAC™ to
ON
or AUTO.
8. Begin use according to tool manufacturer instruc-
tions.
9. Always hold the tool securely using both handles
to maintain control.
Attaching the HAMMERVAC™ to a Rotary
Hammer/Hammer Drill
The HAMMERVAC™ is provided with a clamping
collar assembly and one side handle grip.
1. Turn
OFF
, remove the battery pack from the
HAMMERVAC™, and disconnect power from
the tool.
2. Remove the tool side
handle by flipping
clamp lever upwards.
3. S l i d e
t h e
HAMMERVAC™ side
handle clamping col-
lar assembly over the
chuck and onto the
neck of the tool.
4. Attach the side handle
clamping collar assem-
then lower jaw.
5. Press down the clamp lever to secure the clamping
collar assembly to the HAMMERVAC™.
6. Rotate the HAMMERVAC™ and side handle grip
to the desired position and tighten securely.
5
NOTE:
When using the optional Crevice Tool (Cat.
No. 49-90-2325), set the drill depth to 0.
Drill Depth
Clamp
lever
Upper
Jaw
Lower
Jaw
Summary of Contents for HAMMERVAC M12 UDEL
Page 7: ......