CAUTION
HAMMERVAC™ is largely depen-
clean with water or compressed air. Remove from
dust box and tap clean.
•
•
•
•
Installing/Removing Nozzle Assembly
To install the nozzle assembly
supplied with the tool, or acces-
sory nozzles:
1. With the nozzle assembly
pointing straight up, line up the
lugs of the nozzle assembly
with the lugs on the front of the
HAMMERVAC™. The unlock
symbol
on the nozzle as-
sembly will line up with the
depth gauge on the top of the
HAMMERVAC™.
2. Turn the nozzle assembly left
or right to lock into place. The
lock symbol on the nozzle
assembly will line up with the
depth gauge on the top of the
HAMMERVAC™.
3. To remove, reverse the proce-
dure.
Installing/Removing Nozzle
Replace the nozzle:
After drilling about 1500 holes,
When the bit brush shows signs
of wear,
When suction is reduced,
When dust escapes through the
bit brush during use
To replace the Standard (Cat.
N o . 1 4 - 5 2 - 0 1 0 5 a n d L a r g e
Cat. No. 14-52-0110) nozzles, ro-
tate the nozzle release lever up to
the open position and pull out nozzle from the lower
nozzle assembly(Cat. No. 42-20-0615). Slide the new
nozzle into the lower nozzle assembly and rotate the
nozzle release lever down to the closed position.
SPECIFICATIONS
Cat. No. .................................................M12 UDEL
Dust Box Cat. No .................................. 42-16-0580
Crevis Tool Cat. No ............................... 49-90-2325
Volts............................................................12V DC
Battery Type .................................................M12™
Charger Type................................................M12™
Max depth........................................... 203 mm (8”)
Min Bit Diameter ................................ 4 mm (5/32")
Max Bit Diameter............................. 32mm (1-1/4")
Hammer Collar Sizes
Diameter
Circumference
Ø 41-61 mm (1.6"-2.4")
129-192 mm (5.1"-7.5")
Recommended Ambient Operating Temperature
...................................-17°C to 51°C (0°F to 125°F)
Dust box
port
HEPA
6. If necessary, pull the
the dust box and tap
HEPA filter away from
clean. Do not clean
with water or compressed air. After about 1500
HEPA filter (Cat. No. 49-90-2306).
To
install
the dust box:
1. Slide the dust box into the body of the
HAMMERVAC™.
2. The dust box latches should snap into place.
NOTE:
Do not operate the HAMMERVAC™ without
ADDITIONAL BATTERY SAFETY RULES
WARNING
To reduce the risk of fire,
personal injury, and product
damage due to a short circuit, never immerse your
tool, battery pack or charger in fluid or allow a fluid
to flow inside them. Corrosive or conductive fluids,
such as seawater, certain industrial chemicals, and
bleach or bleach-containing products, etc., can
cause a short circuit.
WARNING
Do not charge
non-rechargeable batteries.
4
ASSEMBLY
WARNING
Recharge only with the charger
-
manual supplied with your charger and battery.
Removing/Inserting the Battery
To
remove
the battery, push in the release buttons
and pull the battery pack away from the tool.
WARNING
Always remove battery pack before
changing or removing accessories.
To
insert
the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
WARNING
recommended for this tool. Others
may be hazardous.
To reduce the risk of injury, always remove the
battery pack before removing the dust box. Do
in place.
Installing/Removing the Dust Box
and HEPA Filter
To
remove
the dust box:
1. Turn
OFF
the tool.
2. Remove the battery pack.
3. Press the dust box latches. (1)
4. Pull the dust box away from the
1
2
HAMMERVAC™. (2)
5. Empty debris by holding away
from the user’s face and tap-
ping dust box into a trash can,
pail, or other reasonable con-
tainer. For best cleaning
results, connect a
vacuum hose with dust
extraction adaptor (Cat
No. 49-90-1959) to the
dust box port and suc-
tion out debris.
Summary of Contents for HAMMERVAC M12 UDEL
Page 7: ......