Milwaukee 4933451012, Original Instructions Manual

Page: 24 / 26

22 22
XII
English
For battery pack storage longer than 30 days: Store the battery
pack where the temperature is below 27°C and away from moisture
Store the battery packs in a 30% - 50% charged condition Every six
months of storage, charge the pack as normal.
Do not dispose of used battery packs in the household refuse or
by burning them. Milwaukee Distributors offer to retrieve old
batteries to protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
No metal parts must be allowed to enter the battery section of the
charger (short circuit risk).
Battery acid may leak from damaged batteries under extreme load
or extreme temperatures. In case of contact with battery acid wash
it off immediately with soap and water. In case of eye contact rinse
thoroughly for at least 10 minutes and immediately seek medical
attention.
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit situa-
tions that cause high current draw, the tool will vibrate for about 5
seconds, the fuel gauge will flash,and then the tool will turn OFF.
To reset, release the trigger. Under extreme circumstances, the
internal temperature of the battery pack could raise too much. If
this happens, the fuel gauge will flash until the battery pack cooled
down. After the lights go off, the work may continue.
Place the battery on the charger to charge and reset it.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods Legisla-
tion requirements.
Transportation of those batteries has to be done in accordance with
local, national and international provisions and regulations.
The user can transport the batteries by road without further
requirements.
Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation and
transport are exclusively to be carried out by appropriately trained
persons and the process has to be accompanied by corresponding
experts.
When transporting batteries:
Ensure that battery contact terminals are protected and insulated
to prevent short circuit.
Ensure that battery pack is secured against movement within
packaging.
Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
MAINTENANCE
Before use check machine, cable, safety harness and plug for any
damages or material fatigue. Repairs should only be carried out by
authorised Service Agents.
The ventilation slots of the machine must be kept clear at all times.
From time to time, apply a few drops of oil to the rack toothing. The
bearings of the feed shaft are self-cutting and must not be greased.
Grease the sliding surface of the carriage with Molykote grease.
Clean dust and debris from tool. Keep tool handles clean, dry and
free of oil or grease. Use only mild soap and a damp cloth to clean
the tool since certain cleaning agents and solvents are harmful
to plastics and other insulated parts. Never use flammable or
combustible solvents around tools.
Use only Milwaukee accessories and Milwaukee spare parts. Should
components need to be replaced which have not been described,
please contact one of our Milwaukee service agents (see our list of
guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the Article No. as well as the machine type printed on the
label and order the drawing at your local service agents or directly
at: Techtronic Industries GmbH, Max-Eyth-Straße 10, 71364 Win-
nenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any work on the
appliance.
Always work in pairs when using the drill stand above
head height. Carry the electric tool between the two of
you to avoid suffering back injuries.
Please read the instructions carefully before starting the
machine.
Always wear goggles when using the machine.
Wear ear protectors!
Wear gloves!
DANGER! To reduce the risk of injury, always keep hands,
rags, clothing, etc. away from moving parts and chips. Do
not try to remove chips while the cutter is rotating. Chips
are sharp and can pull objects into moving parts.
Carrying along metal parts and watches is prohibited.
Persons with cardiac pacemakers or other medicinal
implants may not use this drill stand.
Carrying of magnetic or electronic media prohibited.
Never expose tool to rain.