
Ê
Applying Threadlocker
NOTE: The following threadlocker information and
illustrations are excerpts from the Loctite
®
User’s
Guide and are used with permission.
For maximum strength, threadlocker must fill the thread
voids completely, as shown in FIGURE 2. Organic or petro-
leum solvent will remove excess uncured adhesive from
joints. Consult information below for the specific fastener ap-
plication.
Ë
Bolts and Nuts
—See FIGURE 3.
1. Clean all threads (bolt and nut) with cleaning solvent.
2. Spray all threads with Loctite
®
Primer N. Allow to dry.
3. Insert bolt into through hole assembly.
4. Apply several drops of threadlocker onto bolt engage-
ment area.
5. Assemble and tighten nut to correct torque for the
threadlocker.
Ë
Blind Holes
—See FIGURE 4.
1. Clean all threads (bolt and nut) with cleaning solvent.
2. Spray all threads with Loctite
®
Primer N. Allow to dry.
3. Squirt several drops down female threads into bottom of
hole.
4. Apply several drops to bolt.
5. Tighten to correct torque for the threadlocker.
Î
FIGURE 2
(MSSM0101CE)
Î
Correct Threadlocker Use
Apply here
Not here
Î
FIGURE 3
(MSSM0101CE)
Î
Applying Threadlocker to
Through Hole
Onto
threads
Onto
threads
Î
FIGURE 4
(MSSM0101CE)
Î
Applying Threadlocker to Blind Holes
MSSM0101CE/9906AV (2 of 19)
42
Summary of Contents for 60044 SG2
