5142019
17
STEP 8: Connect the two (2) seat hinges to the vertical supports using two (2) 2” bolts, four (4) washers, two (2) black Teflon washers, and
two (2) locknuts as shown in Figure 23.
STEP 9: Bolt the vertical uprights and the rear platform support tube to the platform using four (4) 1 3/4” bolts, eight (8) washers, and four
(4) locknuts as shown in Figure 24.
Make certain to place a washer under the head of each bolt and under each locknut.
STEP 10: Assemble the two (2) sections of shooting rail using two (2) 1 1/2” bolts, four (4) washers, and two (2) locknuts as shown in
Figure 25. Install the assembled shooting rail onto the uprights using two (2) 2 3/4” bolts, six (6) washers, and two (2) locknuts as shown in
Figure 25. Make certain to place a washer under each bolt head, between the shooting rail and upright, and under each locknut as shown
in Figure 25.
WARNING! Prior to attempting to use this or any other Millennium product(s) you must take a moment and become fa-
miliar with it’s setup and installation at ground level. You must practice installing, setting-up and using this product(s) at
ground-level prior to attempting to use it at heights above ground-level. Once you have become thoroughly knowledgeable
and comfortable with this Millennium product(s) setup, installation and use at ground-level - you’re now ready to use it at
heights above ground-level. Failure to follow these instructions may result in serious injury or death!
WARNING! You must wear the factory provided full-body fall arrest harness included with this product at all times during
use of this product. Failure to follow these instructions may result in serious injury or death!
WARNING! Never climb, install or use a treestand with a single safety belt or chest harness. These devices have been
deemed unsafe for use in climbing apparatus applications and may endanger your personal safety. Use only the factory
provided full-body fall arrest harness which meets or exceeds industry standards recognized by the TMA or an aftermarket
full-body fall arrest harness system which meets or exceeds industry standards recognized by the TMA. Failure to follow
these instructions may result in serious injury or death!
WARNING! DO NOT use this, or any other product(s) to climb utility poles, telephone poles, structural columns or any other
man-made structures. Never use this or any other product(s) around power generation (transformers, generators, substa-
tions, etc.) and/or power transmission equipment (power lines). Failure to follow these instructions may result
in serious injury or death!
WARNING! Do not use this or any other product(s) if you have a history of heart problems, back problems, impaired vision,
equilibrium problems, high blood pressure or any other physical impairment that may limit your ability to use and/or operate
this product(s) in the safe manner outlined in this Instruction Manual. Additionally, do not use this or any other product(s) if
you are currently taking any medication and/or substance, including alcohol, that may limit your ability to use this product(s)
as outlined and described in this Instruction Manual. Failure to follow these instructions may result in serious injury or death!
INSTALLING MILLENNIUM L-220-SL 18’ DOUBLE LADDERSTAND
Figure 24
Install Vertical Supports
and Rear Platform Support Tube
Figure 25
Install Shooting Rail
Figure 26
Install Footrest
STEP 11: Install the foot rest to the uprights using two (2) 3” bolts,
eight (8) washers, and two (2) locknuts as shown in Figure 26. Make
certain to place two (2) washers between the foot rest and upright,
one (1) washer under the bolt head, and one (1) under the locknut
as shown in Figure 26. Go back now and tighten the hardware to 50
inch pounds. Make certain all hardware is secure prior to attempting
to use this product(s).
STEP 12: With the assembly still laying on the ground, install the
ladder sections by pinning them together using the spring pins. Make
certain the spring pins engage each ladder section as shown in Fig-
ure 27 and the spring clips are fully engaged as shown in Figure 28.
WARNING! The spring pins and spring clips must be positively
engaged on each ladder sections. Failure to engage these
spring pins as outlined will result in the ladder sections sepa-
rating as you climb. Failure to follow these instructions may
result in serious injury or death!
Figure 28
Secure Ladder Sections
with Spring Pins
Spring Clip
Engaged
Figure 27
Assemble Ladder Sections
