background image

4

1. Product Introduction

1.1 Overview

EM310-UDL is a LoRaWAN

®

ultrasonic distance/level sensor mainly used for detection of waste

bin and other container’s level. With a compact size and wide measure range, EM310-UDL can
be installed to any types of waste bins or containers to monitor solid or liquid level. Besides,
EM310-UDL equips with 3-axis accelerometer to detect the status of container cover. It is
equipped with NFC (Near Field Communication) and can easily be configured by a smartphone.

Sensor data are transmitted in real-time using standard LoRaWAN

®

protocol. LoRaWAN

®

enables encrypted radio transmissions over long distance while consuming very little power.
The user can obtain sensor data and view the trend of data change through Milesight IoT Cloud
or through the user's own Network Server.

1.2 Features

3 to 450 cm wide measuring range with short bind zone

Support temperature compensation for high accuracy

Up to 15 km communication range

Easy configuration via NFC

Standard LoRaWAN

®

support

Milesight IoT Cloud compliant

Low power consumption with 7000mAh replaceable battery

2. Hardware Introduction

2.1 Packing List

1 × EM310-UDL

Device

2 × Mounting

Kits

2 × Screw

Caps

1 ×

Warranty Card

1 ×

Quick Guide

If any of the above items is missing or damaged, please contact your sales representative.

Summary of Contents for EM310-UDL

















Reviews: