Mighty sun BRACELESS OVAL POOLS Universal Instructions Download

Page: 10 / 12

DO NOT FASTEN THE WALL WITHOUT USING THE REINFORCING
WASHERS ! FAILURE TO USE REINFORCING WASHERS AS
INSTRUCTED WILL CAUSE WALL TO SPLIT WHEN POOL IS FILLED.
THIS CAN CAUSE SERIOUS PROPERTY DAMAGE AND/OR BODILY
INJURY.

INSERT THE SCREWS FROM INSIDE OF WALL.
NUT MUST BE FASTENED FROM OUTSIDE OF
WALL.

* Reinforcing Washers must be on INSIDE and OUTSIDE of wall.
* Insert the screws from INSIDE of the wall.
* Insert and fasten screws from hole to hole down to the bottom

of the wall.Do not fasten tightly before insert all screws.

* Fasten all screws tightly.

* Do not leave any open holes.
* Cover all the screw heads with strip of fabric tape.
* Check the level of the top of the wall,if more than 2" off level ,

Rework the ground to achieve levelness.

Unfold the liner inside the metal wall. Carefully spread it out on
the ground. The seam around the bottom of the liner should be
well up the earth mound. Do this evenly all around pool.

Remove your shoes. The liner should never be forcefully pulled
or dragged, especially when it holds water, even only 1/2".
When you enter the pool during installation, use a ladder other
than a pool ladder.
Make sure the legs rest on a strong flat board

Open the liner carton carefully by removing the tape. (Do not
cut open carton.)

For untirusting, All edges of cut out have to be covered by vinyl
tape or rusting paint.
Begin the installation of the through the wall skimmer.

separate skimmer installations.

At one point during the installation of the skimmer, you have to
install the liner. The skimmer installation will tell you when.
Complete the installation of the liner as described next. Then
finish the skimmer installation.

Build a mound 6" high and extending 8 to 10" on the ground
around the inside of the pool wall. Pack the earth gently but
firmly.

9) BUILD AN EARTH MOUND(cove)

The earth mound must be built right. you must rebuild the earth mound each
time you set up the pool. Water pressure can force the liner out under the
bottom rail.

If this is not done.This could cause damage to the liner and void

warranty. The earth mound will prevent this from happening.

11) LINER INSTALLATION

10) THROUGH THE WALL SKIMMER

Remove top rail temporarily placed.
Lift the side of the liner over the top of the wall. Form a collar
approximately 3" down the outside of the wall and temporarily
tape it, to the outside of the wall using masking tape at intervals
of 3'.

Take the plastic edging and clip it over the liner and the top of
the wall. The ends of each section of edging should touch
each other. The edging forms a full circle all around. Cut
off excess plastic edging

If the liner does not fit evenly around the pool.
Remove the masking tape gently from the collar of the liner and wall.
Smooth out all wrinkles on the bottom of the liner. There may be
extra material around the side. Spread it evenly all around the side of
the pool. There may be extra material in height.

IMPORTAN
T:

Step 2:

Step 1:

CAUTION:

Step 1:

Step 3:

Step 4:

4)
To keep the water clean and protect your liner from being damaged it is
best to cover hose end(s) with several layers of rags.

3)
Set as many hoses as you want to help speed up filling time. The pool
holds a considerable amount of water (ie;18' round pool holds 7650
gallons.).

2)
Measure all around the pool, from the TOP RAIL down to WATER
LEVEL. This level SHOULD NOT VARY MORE THEN ONE INCH.
An unleveled condition will cause overstress of the pool wall and frame.
Remove excess soil as required to establish a level frame and bottom
rail condition.

See " ASSEMBLY OF BOTTOM RAILS "

1)
INSPECT BOTTOM RAILS-make sure they are not scalloped, see
detail at right. If rails scallop, pull outward at the bottom of the
verticals to allow wall and rails to assume natural shape.
By using a string and small weight, check each vertical.To see that they
stand straight.
Be sure each vertical stands perfectly straight.

IMPORTANT: STOP FILLING POOL AT 1 FOOT DEPTH

When pool is completely assembled and ready for water, run water into
the pool. Wrinkles in pool liner should be smoothed out as water is
added for easier maintenance.

The hard work is all behind.
Now the fun begins.

12) FILLING THE POOL

CAUTION:
Do not attempt to straighten liner after you begin to fill with water.
Severe damage could be caused and You will void warranty.

5)
When desired water level is reached, turn on your filter.

(Follow separate instructions provided with your filter.)

2in

6in

1/4in Reinforcing Washer

INSIDE OF POOL

Please refer to "Assemble TopSeat ,
Vertical and Cover" of an attached sheet

Meijer.com