WARNING! This device is not intended for use
with emergency exit fixtures or
emergency exit lights.
WARNING! Permanent damage to the low
voltage 14VAC lamp will occur if installed
on a 120VAC circuit.
PureWhite Replacement LED In-Ground Pool and Spa lamps are available
in 14VAC (low voltage) and 120VAC models as indicated on the product
packaging. Each lamp has a screw-in Edison base.
WARNING! Remove warning label from
PureWhite lens before installation.
[Applies only to model #s: LPL-P1-WHT-12-S and LPL-P1-WHT-120-S]
The warning label is placed on top of a special optical diffuser designed
to maximize the light projection of the PureWhite lamp. When you remove
the label, a protective film will come off with it. Once the warning label
and protective film have been removed, do not allow the diffuser decal
underneath to be scratched.
ATTENTION 14V PUREWHITE OWNERS!
A socket voltage range of 13.5 – 15.0 will achieve optimal brightness.
To verify the voltage, at the lamp socket, measure the open circuit
voltage (no lamp in the socket). Set the transformer tap to 14.0VAC.
DANGER!
Risk of electrical shock or electrocution
Always disconnect power to the pool or spa light at the circuit
breaker panel before attempting to service the lamp. Failure to do so could
result in serious injury or death due to electrical shock. Refer to the original
manufacturer’s light installation manual before proceeding. As with any
electrical device, installation and service should always be performed by
a qualified individual.
This device is not intended for use in anything
other than in-ground pools or spa.
Rated Lamp Life
The illumination generated by the PureWhite Replacement LED In-Ground
Pool or Spa lamp is based on Light Emitting Diode (LED) technology. The
average expected lamp life is rated up to 25,000 elapsed time hours under
normal operating conditions. [Temperature: 33°F to 104°F (1°C to 40°C),
Humidity: 0-95% non-condensing].
Safety Precautions
• Do not open, service or tamper with any internal component of the
PureWhite Replacement LED In-Ground Pool or Spa lamp. Doing
so will void the warranty. Follow each instruction in this owner’s
manual and pay careful attention to all warnings.
• Do not directly expose or immerse the PureWhite Replacement LED
In-Ground Pool or Spa lamp in water without containing it in a
proper, watertight, NRTL (nationally recognized testing laboratory)
light housing and niche assembly.
• Keep the light housing dry.
• Handle the PureWhite Replacement LED In-Ground Pool lamp with
care. Be careful not to drop the unit.
IMPORTANT NOTE:
PureWhite lamps are recommended for installation by a qualified pool or
spa professional.
J&J Electronics
•
35 Hammond, Irvine, CA 92618 USA
•
800.735.4553
•
949.455.4460
•
www.jandjpoolspa.com
PAGE 1
PureWhite
™
Pool & Spa Lamp Installation and Operation Guide
PUREWHITE REPLACEMENT LED IN-GROUND POOL & SPA LAMPS
Model #s: LPL-P1-WHT-12-S, LPL-P1-WHT-120-S, LPL-M1-WHT-12, LPL-M1-WHT-120
PureWhite Replacement LED In-Ground Pool and Spa lamps offer superior, bright white illumination for your pool or spa. This owner’s manual contains
important information on installing and using your new PureWhite Replacement LED In-Ground Pool or Spa lamp. Please read it carefully and keep it in
a safe place for future reference.
Installation
The installation steps in this owner’s manual
are intended as guidelines. For specific
instructions on how to replace a pool or spa
lamp, please refer to the original manu-
facturer’s light installation manual before
proceeding.
Light housing compatibility
LPL-P1-WHT-12-S, LPL-P1-WHT-120,
LPL-M1-WHT-12, and LPL-M1-WHT-120
PureWhite Replacement LED In-Ground
Pool and Spa lamps must be installed in
a compatible NRTL pool light housing.
Compatible NRTL light housings include:
Hayward
®
Astrolite
™
SP058 Series
Pentair
®
Amerlite 784 Series
Jacuzzi
®
Full Moon
™
Hayward
®
Astrolite
™
II SP059 Series
Pentair
®
SpaBrite
™
Series
WARNING!
Read this before attempting installation
Your PureWhite lamp is not an ordinary light bulb. It is a valuable
electronic device that is not designed to come in direct contact with water.
An improper installation that results in water leakage into the light housing
can permanently damage the PureWhite lamp. Please read these
installation steps and the original manufacturer’s light installation manual
carefully before proceeding.
STEP 1
Remove light housing from niche
Make sure power to the pool or spa light is turned off at the circuit breaker.
Carefully remove the existing light housing from the niche assembly and
place it on the deck. There should be enough power cord to do this easily.
If there is not enough power cord to allow the light housing to reach the
deck surface, call your local pool or spa service company.
WARNING! Verify that your PureWhite lamp
voltage rating (120VAC or 14VAC) matches
your electrical system’s voltage requirements
before proceeding with installation.
