background image

UNIVERSAL INSTRUCTIONS

BRACELESS OVAL POOLS

PLEASE READ THESE INSTRUCTIONS CAREFULLY AND THOROUGHLY BEFORE 
STARTING GROUND PREPARATION AND POOL ASSEMBLY.
DOING SO WILL PREVENT PROBLEMS.

Oval Pool: General informaition ----------------------------------- 

1) Selection of pool site --------------------------------------------
2) Ground preparation ----------------------------------------------
3) Assembling side structual component -----------------------
4) Drawing pool shape ----------------------------------------------
5) Connecting tension straps --------------------------------------
6) Positioning assembled oval parts -----------------------------
7) Assembling bottom rail ------------------------------------------
8) Installing wall -------------------------------------------------------
9) Build an earth mound(Cove) ----------------------------------- 

10) Through the wall skimmer --------------------------------------
11) Liner installation ---------------------------------------------------

Please refer to "Assemble TopSeat , Vertical and Cover" of an attached sheet.

12) Filling the pool -----------------------------------------------------
13) Helpful information -----------------------------------------------
14) SAFETY RULES --------------------------------------------------
BRACELESS OVAL Parts List -------------------------------------

1
1
2
3
5
7
7
8
8
9
9
9

9

10
10
11

Page.

Meijer.com

Summary of Contents for BRACELESS OVAL POOLS













Reviews: