background image

 

MM660 Installation Instructions

  

6

Vehicular Gate

Leading Edge

of the gate

Photo Beams

(recommended, not included)

Sensing Edges

(recommended, not included)

For the Installer and End User

Important Safety Information

Mighty Mule gate operators utilize Dual Sense Tech-

nology™ entrapment protection. Dual Sense Technol-

ogy™ is built into every Mighty Mule and provides 

redundant methods of entrapment protection for open 

and close gate directions.

 

In addition to Dual Sense Technology, every Mighty 

Mule gate controller has provisions for the connection 

of additional obstruction detection devices such as 

sensing edges and photo beams.

These devices may be located where there is an 

increased risk of obstruction. Refer to the diagram 

below.  

 

One or more edge sensors may be located at the lead-

ing edge, bottom edge, and post edge, both inside and 

outside of a vehicular swing gate system.

    

Wiring to sensors must be located and arranged so the 

wiring between the sensor and the gate operator is not 

subjected to mechanical damage.

    

A wireless sensor such as one that  

transmits radio frequency (RF) signals to the gate 

operator for obstruction protection functions shall be 

located where the transmission of the signals is not 

blocked or impeded by building structures, natural 

landscaping or similar objects.

Entrapment Alarm

The Mighty Mule Automatic Gate Operator is designed to stop and reverse the gate when the gate comes in contact with 

an obstruction. Additionally, these operators are equipped with an audio entrapment alarm which will activate if the unit 

obstructs twice while opening or closing. This alarm will sound for a period of 5 minutes, or until the operator receives 

an intended signal from a hard wired entry/exit source (e.g. push button control or keypad) and the gate returns to a fully 

open or fully closed position. Turning the power switch on the control box OFF and back ON will also deactivate the 

alarm. Wireless controls such as transmitters and wireless keypads will not deactivate the alarm.

Entrapment and Obstruction Protection 

Mighty Mules’s Dual Sense Technology

 provides entrapment protection, even when properly adjusted. Since all 

installations are different, you may need to add photo beams or sensing edges to help prevent damage to vehicle or other 

items that could be hit by a moving gate.

Summary of Contents for MM660














































Reviews: