Mighty Mule MM571W Installation Manual Download | Manualshive

Page: 44 / 56

background image

28

MM571W / MM572W Installation Instructions

●

Monthly, test the obstruction and entrapment protection systems.

●

Monthly, service the gate operator (make sure the power switch is OFF). Clean extended operator arm with
a soft, dry clean cloth.

●

On all gates weighing 250 lb. or more, routinely grease the ball bearing hinges at least 4 times a year; more
frequently if the gates are near a coastal area.

●

Monthly, turn off the power switch and disconnect the Mighty Mule and move the gate to make sure the
gate is moving freely without sticking or binding. Lubricate the hinges or repair the gate as required before
reattaching the Mighty Mule.

●

Monthly, check the gate system for potentially entrapments from new landscaping or construction.
Eliminate or guard as required.

●

Monthly, check that the warning signs are mounted on each side of the gate and clearly visible. Replace the
signs if they are missing or damaged.

●

Replace batteries every 2-3 years and properly recycle old batteries.

Maintenance

«
...
42
43
44
45
46
...
»

Summary of Contents for MM571W

























































Reviews:

No comments

Related manuals for MM571W

Brand: V2 Pages: 29

Brand: CAME Pages: 96

Brand: Liftaway Pages: 19

Brand: tau Pages: 4

LiftMaster Professional 78LM

Brand: Chamberlain Pages: 2

Brand: Mach Power Pages: 28

Brand: BEA Pages: 8

Brand: BEA Pages: 16

Brand: CAME Pages: 12

Brand: CAME Pages: 28

Brand: Delton Pages: 8

e-Gate SLD-24V-D

Brand: Grant's Automation Pages: 40

Brand: vds Pages: 25

Brand: V2 Pages: 48

Brand: CAME Pages: 72

Brand: FAAC Pages: 4

Brand: CAME Pages: 28

RADIOSENS RSEC3

Brand: JCM Technologies Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands