Miele W 1716 Operating Instructions Manual Download Page 46 | Manualshive

Page: 46 / 64

background image

Levelling the machine

The machine must stand perfectly level
on all four feet to ensure safe and
proper operation.

Incorrect installation may increase
electricity and water consumption and
may cause the machine to move about.

Screwing out and adjusting the feet

The four adjustable screw feet are used
to level the machine. All four feet are
screwed in when the machine is
delivered.

^

Using the spanner supplied turn
counter nut

2

in a clockwise

direction. Then turn counter nut

2

together with foot

1

to unscrew.

^

Use a spirit level to check the
machine is standing level.

^

Hold foot

1

securely with a pipe

wrench. Turn counter nut

2

again

using the spanner supplied until it
sits firmly up against the housing.

,

All four counternuts must be

firmly up against the housing. Please
also check this for the feet which did
not need adjustment. Otherwise
there is the danger of the machine
moving about.

Installation and connection

46

«
...
44
45
46
47
48
...
»

Summary of Contents for W 1716

































































Reviews:

No comments

Related manuals for W 1716

Brand: FRAM Pages: 58

Brand: Kärcher Pages: 12

Conservator 3953964

Brand: Crosley Pages: 12

Brand: Gaggenau Pages: 56

Brand: Asko Pages: 16

Brand: NEFF Pages: 29

Brand: Fisher & Paykel Pages: 5

Brand: IPC Pages: 104

Brand: Gaggenau Pages: 68

Brand: Kärcher Pages: 32

Brand: Landa Pages: 36

Brand: Smeg Pages: 29

Brand: Fieldmann Pages: 135

Brand: Fagor Pages: 26

Brand: Crest Audio Pages: 47

Brand: Bush Pages: 38

Brand: Lavor Pages: 56

Brand: Sealey Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands