Miele TXD 160 WP Operating Instructions Manual Download Page 51

Page: 51 / 88

Frequently Asked Questions

Problem

Possible cause and solution

Lines flash and light up
after switching on:

  

Program selection is
not possible.

Access via a PIN code has been activated.



See “Programmable functions”, “



PIN code”.



and another number

combination flash after
a program has been
cancelled, a signal
sounds.

There is no obvious cause.



Switch the dryer off and then on again.



Start a program.

If the program is interrupted again and an error
message appears, there is a fault. Contact Miele
Technical Service.





lights up and the

program has been
cancelled, a signal
sounds.

The laundry is unevenly distributed or has rolled up.



Untangle the laundry and remove a few items if
necessary.



Switch the dryer off and then on again.



Start a program.



lit and program start

is not possible.

An update is available for the tumble dryer. See
“Programmable functions –



RemoteUpdate” for

more information.

Summary of Contents for TXD 160 WP

























































































Search results

Summary of Contents for TXD 160 WP

Reviews:

Related manuals for TXD 160 WP

Brands by name

Popular brands

Miele TXD 160 WP, Operating Instructions Manual

Search results

Summary of Contents for TXD 160 WP

Reviews:

Related manuals for TXD 160 WP

Brands by name

Popular brands