background image

Problem solving guide

66

With the help of the following guide, minor faults in the performance of the
appliance, some of which may result from incorrect operation, can be remedied
without contacting Miele. This will save you time and money because you won't
need a service call.

Please note that a call-out charge will be applied to unnecessary service visits
where the problem could have been rectified as described in these operating
instructions.

Fault messages shown in the display when a programme is
cancelled

Message

Possible cause and remedy

Clean the fluff filter.
Check the airways.

The system is clogged by fluff or detergent
residues.

To deactivate the message, confirm with 

OK

.

Clean the fluff filters and the plinth filter.

Please see "Cleaning and care" for notes on
cleaning.

The fluff and/or plinth filters are damaged or
deformed.

Check the fluff filters and the plinth filter. Replace
them if necessary.

The fluff and/or plinth filters are clogged. It is no
longer possible to clean them.

Check the fluff filters and the plinth filter. Replace
them if necessary.

For information on when to replace a plinth filter that
is not functioning properly, refer to "Problem solving
guide - Replacing the plinth filter".

Summary of Contents for TWR 780 WP













































































































Reviews: