Miele TEL 785 WP Operating Instructions Manual Download Page 40

Page: 40 / 100

Programme chart

All weights marked with * are based on the weight of dry laundry.

Programmes on the control panel

Cottons



max.

9 kg*

Use for

Cotton items such as those described under

Cottons Normal

with

normal residual moisture.

Note

- Items are dried to a

Normal

level only in this programme.

- The

Cottons



programme is the most energy-efficient for dry-

ing cotton items with normal residual moisture levels.

Note for
test insti-
tutes

- The

Cottons



programme is the test programme in accord-

ance with Regulation 392/2012/EU for energy labelling, measured
in accordance with EN 61121.

- With the

Cottons

and

Cottons



programme settings, drain the

condensed water externally through the drain hose.

Summary of Contents for TEL 785 WP





































































































Search results

Summary of Contents for TEL 785 WP

Reviews:

Related manuals for TEL 785 WP

Brands by name

Popular brands

Miele TEL 785 WP, Operating Instructions Manual

Search results

Summary of Contents for TEL 785 WP

Reviews:

Related manuals for TEL 785 WP

Brands by name

Popular brands