Miele T 8903 C Operating Instructions Manual Download Page 44

Page: 44 / 48

Changing the "Delicates"
programme selection

The drying result is set to the stan-
dard drying level

Normal

You have the possibility to switch to

Hand iron

(more moisture) or

(drier than the standard

drying level).

Follow steps (

...) with the

help of the

Start

button and

programme selector to programme
and store in memory.

Before you begin, first ensure that:

– The dryer is switched off.

– The door is closed.

– The programme selector is turned to

Finish

Press the

Start/Stop

button and keep

it pressed in whilst carrying out steps

Switch the dryer on.

Wait until

Start

lights up

constantly. . .

. . . and then release the

Start

button.

Turn the programme selector to

Cottons Hand iron

The

Finish/Anti-crease

indicator light

will flash 5 times.

The

flashing

Drying

indicator light

shows which option is selected.

– The

Drying

indicator light doesn't

flash:

Standard Drying level becomes

Hand iron.

– The

Drying

indicator light flashes

once:

Factory default setting.

– The

Drying

indicator light flashes

twice:

Standard Drying level becomes

You can switch from one option to
the other by pressing the

Start

button

(

Drying

indicator light).

Switch the dryer off.

The setting you have selected is now
stored in memory. You can alter the
settings again at any time.

Control

Repeat steps

After checking the indicator lights
(see above), switch the dryer off.

Programmable functions

Summary of Contents for T 8903 C

















































Search results

Summary of Contents for T 8903 C

Reviews:

Related manuals for T 8903 C

Brands by name

Popular brands

Miele T 8903 C, Operating Instructions Manual

Search results

Summary of Contents for T 8903 C

Reviews:

Related manuals for T 8903 C

Brands by name

Popular brands