Miele T 8623 C Operating Instructions Manual Download Page 25

Page: 25 / 56

Changing a programme while it
is running

You cannot change to another
programme once a programme has
started (this prevents unintentional
alterations).
If an attempt is made to change a
selection,

Option not possible

will

appear in the display.

It is still possible to select or deselect
the

Anti-crease

and

Buzzer

extra

options.

You will need to cancel the current
programme before you can select a
new one.

Cancelling a programme

Press the

Start/Stop

button.

The "Stopped" option

Cancel

programme

will appear in the display.

Confirm by pressing the right hand

button under

The items will be cooled down,
depending on the temperature
reached and how long they have
been dried for.

If you press the

Start/Stop

button

during the cooling down phase and
confirm by pressing the right hand

button under

Finished

will

appear in the display.

Switch the dryer off and then on
again.

You can now select a different
programme.

Note: A programme can also be
interrupted by turning the programme
selector to

Stop

Interrupting a programme

Switch the dryer off.

To continue drying

Switch the dryer on.

The programme will continue, as long
as the cooling down phase has not
been reached.

Adding or removing laundry
after a programme has started

Press the

Door

button.

Open the door.

Do not touch the back of the

drum when adding or removing
items. The drum could be very hot -
danger of burning.

Add or remove items as required.

Close the door.

Press the

Start/Stop

button.

Note

The time remaining shown in the
display may now vary from the actual
drying time.

Changing the programme sequence

Summary of Contents for T 8623 C

























































Search results

Summary of Contents for T 8623 C

Reviews:

Brands by name

Popular brands

Miele T 8623 C, Operating Instructions Manual

Search results

Summary of Contents for T 8623 C

Reviews:

Brands by name

Popular brands