manualshive.com logo in svg

Miele T 8623 C, Operating Instructions Manual

Share
Download
Miele T 8623 C Operating Instructions Manual Download Page 10

Control panel

a

Start/Stop button

For starting the programme selected
and cancelling a programme once it
has started.
The indicator light flashes while a
programme is being selected and
then is on constantly when the
programme has started.

b

Display with Menu buttons

See the next page for more
information.

c

m

button

For selecting delay start and calling
up the time of day in the display.

d

PC / Optical interface

This is used by service technicians
to run diagnostic checks on your
machine and can also be used to
update programming data in the
future.

e

Extra option buttons

Various extra options can be added
to the drying programmes.

f

Programme selector

The programme selector can be
turned clockwise or anti-clockwise.

g

I-On/0-Off button

To switch the machine on or off or to
interrupt a programme.

h

Door button

Pressing this button will open the
door even when the machine is
switched off at the mains.

Operating the tumble dryer

10

Summary of Contents for T 8623 C

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands