Miele T 8001 WP SUPERTRONIC Operating Instructions Manual Download Page 50

Page: 50 / 72

Problem

Possible cause

Remedy

There are humming
noises.

The compressor is
operating.

None. These noises are quite
normal and do not indicate a
fault.

The display and
sensors are dark. The
Start sensor flashes
slowly.

The display and sensor
lighting have switched
off automatically to
save energy.

– Press the

Start

sensor

briefly. The lighting comes
back on again.

– See "Settings menu -

Display / Sensor lighting".

A programme cannot
be started.

There is no immediate
cause.

– Is the dryer switched on?

– Is the mains plug plugged

in?

– Is the door closed

properly?

– Has the fuse or circuit

breaker tripped?

– If you cannot remedy the

problem, there is a fault.
Call Miele.

Power cut.

When power is restored to the tumble dryer after a
power cut, the programme will continue automatically.

The display is in a
different language.

A different language
has been selected.

Set the language you want.
The

flag symbol

will guide

you.

The interior drum
lighting is not
switched on.

The lighting switches
off automatically (to
save energy).

– Switch the dryer off and

then on again.

– If the lamp needs to be

replaced, follow the
instructions in "Changing
the lamp" at the end of this
section.

Access via a code has
been activated.

– After entering the code, the

lamp will light up again.

Problem solving guide

Summary of Contents for T 8001 WP SUPERTRONIC









































































Search results

Summary of Contents for T 8001 WP SUPERTRONIC

Reviews:

Related manuals for T 8001 WP SUPERTRONIC

Brands by name

Popular brands

Miele T 8001 WP SUPERTRONIC, Operating Instructions Manual

Search results

Summary of Contents for T 8001 WP SUPERTRONIC

Reviews:

Related manuals for T 8001 WP SUPERTRONIC

Brands by name

Popular brands