Miele T 7944 C Operating Instructions Manual Download Page 51

Page: 51 / 64

Altering the residual moisture
level in the Minimum iron
programme

The tumble dryer is designed to dry
effectively using as little energy as
possible.
However, if you require the laundry to
be drier or damper, you can reduce
or increase the default residual
moisture in the Minimum iron
programme.

Follow the steps (

...) to

programme and store in memory.

Before you begin, ensure that:

– The tumble dryer is switched off.

– The door is closed.

Press the

Start/Stop

button and keep

it pressed in whilst carrying out steps

Switch the dryer on.

Wait until the

Start/Stop

button lights up

constantly . . .

. . . and then release the

Start/Stop

button.

Press the

Low temperature

button

once.

– The

Low temperature

indicator light

will flash twice briefly.

number

to show which option is

selected will appear in the display
alternating with the letter

Increased residual moisture.
Laundry damper.

Standard residual moisture
(factory default setting)

(the

Automatic plus

indicator light will

also flash once).

Reduced residual moisture.
Laundry drier.

(the

Automatic plus

indicator light will

also flash twice).

Pressing the

Start/Stop

button

switches between the options.

Switch the dryer off.

The setting you have selected is now
stored in memory. You can change it
again at any time.

To check the setting:

Carry out steps

Switch the dryer off after step

Programmable functions

Summary of Contents for T 7944 C

































































Search results

Summary of Contents for T 7944 C

Reviews:

Related manuals for T 7944 C

Brands by name

Popular brands

Miele T 7944 C, Operating Instructions Manual

Search results

Summary of Contents for T 7944 C

Reviews:

Related manuals for T 7944 C

Brands by name

Popular brands