background image

If the connection cable is faulty it
must only be replaced by a Miele

approved service technician to protect
the user from danger.

In the event of a fault or for
cleaning purposes, the machine is

only completely isolated from the
electiricty supply when:

– it is switched off at the wall socket

and the plug is withdrawn, or

– it is switched off at the mains, or

– the mains fuse is withdrawn.

Operation

This equipment is not designed for
maritime use or for use in mobile

installations such as caravans, aircraft
etc. However it may be suitable for
such usage subject to a risk
assessment of the installation being
carried out by a suitably qualified
engineer.

The dryer must not be used without
the fluff filters in place or if the fluff

filters are damaged in any way.

The fluff filters must be thoroughly
dried after cleaning. If they are still

damp or wet when replaced there is a
risk of faults occurring when the
machine is used.

The dryer must not be used without
the condenser unit in place.

Do not install the machine in a
room where the temperature may

drop down to or below freezing. At very
cold temperatures the machine may be
difficult to start.
There is a risk of damage if the
condensed water is allowed to freeze in

the pump, hoses and / or condensed
water container.

If the water is drained externally
through the drain hose instead of

being collected in the condensed water
container, make sure the drain hose is
securely attached if you hang it in a
sink or basin to avoid the hose slipping
and the water causing damage.

Condensed water is not drinking
water. It can cause health

problems in both people and animals.

Always keep the area around the
machine free of dust and fluff. Dust

drawn into the machine can, over time,
cause blockages in the condenser unit.

Warning and Safety instructions

7

Summary of Contents for T 4882 C





























































Reviews: