Miele T 4882 C Operating Instructions Manual Download Page 58

Page: 58 / 60

Stand-by

To save energy, the display goes out after 10 minutes and
the

Start

button flashes slowly.

There are two options:

on (the machine is delivered with this option selected)

Stand-by comes on:

– if a programme is not selected after the machine has been

switched on.

– after the

Start

button has been pressed.

– at the end of a programme.

Not in current prog.

Stand-by comes on:

– if a programme is not selected after the machine has been

switched on.

Operating the multi-function selector or one of the short cut
buttons switches the display back on again.

A tick will appear beside the option to show that it has been
set.

SETTINGS

Back

STAND-BY

Not in current prog.

Select the option you want and confirm your selection.

To close the Settings menu

SETTINGS

Back

LANGUAGE

...

TIME OF DAY ...

DRYING LEVELS ...

Select

Back

and confirm your selection.

The display will revert to the entry menu.

Settings menu

Summary of Contents for T 4882 C





























































Search results

Summary of Contents for T 4882 C

Reviews:

Related manuals for T 4882 C

Brands by name

Popular brands

Miele T 4882 C, Operating Instructions Manual

Search results

Summary of Contents for T 4882 C

Reviews:

Related manuals for T 4882 C

Brands by name

Popular brands