Miele T 284 Operating Instructions Manual Download Page 46

Page: 46 / 48

Standby

To save energy, the programme
sequence/check lamps go out and
the indicator lamp for the

Start

button

starts flashing slowly.

To come out of standby mode

Turn the programme selector or
press the

Start

button. Neither will

have any effect if a programme is
running.

Factory default

The standby function is activated and
the programme sequence/check lamps
will go out after 10 minutes:

– if a programme is not selected after

the dryer has been switched on.

– after a programme has started.

They will, however, come on for 10
minutes at the end of the programme or
the end of the anti-crease phase. The
buzzer (if selected ) will sound for 10
minutes at the end of the programme.

Instead of the factory default setting
you can select another option:

Not in current programme

As described under "Factory default"
above.
However, they will stay on after the
programme has started and remain
visible during the programme.

Off

The programme sequence/check
lamps will stay on while the dryer is
switched on.

Follow the steps (

...) to

programme and store in memory.

See next page.

Programmable functions

Summary of Contents for T 284

















































Search results

Summary of Contents for T 284

Reviews:

Related manuals for T 284

Brands by name

Popular brands

Miele T 284, Operating Instructions Manual

Search results

Summary of Contents for T 284

Reviews:

Related manuals for T 284

Brands by name

Popular brands