Miele PWM 508 Mop Star 80 Operating And Installation Instructions Download Page 26

Page: 26 / 84

3. Selecting a programme

Switching on the washing
machine



Press the



button.

Selecting a programme

Selecting standard programmes with
the programme selector



Turn the programme selector to the
required programme.

The selected programme will be shown
in the display. The display will then
change to the main menu for that
programme.

Selecting further programmes with
the programme selector turned to





Turn the programme selector to the



position.

You can select the required programme
via the display.



Further

progs





New mops

Curtains



Touch the





sensor control until

the programme you want appears in
the display.



Touch the sensor for that programme.

The display will change to the main
menu for that programme.

Summary of Contents for PWM 508 Mop Star 80





















































































Search results

Summary of Contents for PWM 508 Mop Star 80

Reviews:

Related manuals for PWM 508 Mop Star 80

Brands by name

Popular brands

Miele PWM 508 Mop Star 80, Operating And Installation Instructions

Search results

Summary of Contents for PWM 508 Mop Star 80

Reviews:

Related manuals for PWM 508 Mop Star 80

Brands by name

Popular brands