manualshive.com logo in svg

Miele PW 6080 VARIO, Operating And Installation Instructions

Share
Download
Miele PW 6080 VARIO Operating And Installation Instructions Download Page 42

A fault message appears in the display

Message

Possible cause

Remedy

A

p

Water intake fault
Open the stopcock
and
check the inlet hose.

The water inlet is
blocked or restricted.

Check whether

– the stopcock is opened

enough.

– the inlet hose is kinked.

The water pressure is
too low.

– Select

Low water

pressure

in the

Settings/Supervisor level

menu.

,

Technical fault

There is a fault.

Start the programme again.
If the fault message appears
again, contact the Miele Ser-
vice Department.

,

Fault
Disinfection
temperature
not reached

During the disinfection
programme the water
temperature was not
reached.

The machine has

not

carried out the disinfection
cycle correctly.
Start the programme again.

q

Drain fault
Clean the drainage
system.

The water outlet is
blocked or restricted.

Drain pump version: Clean
the drainage system.

Drain valve version: Call
Service.

O

Fill the container

or

One of the external
detergent containers is
empty.

See "Detergent - Empty
sensor".

Fault
Container empty

A

To switch off the fault message, press the multi function selector.

Problem solving guide

42

Summary of Contents for PW 6080 VARIO

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands