manualshive.com logo in svg

Miele PW 6080 VARIO, Operating And Installation Instructions

Share
Download
Miele PW 6080 VARIO Operating And Installation Instructions Download Page 14

Control panel

a

Display

See the following pages for more information.

b

Short cut buttons

For selecting an individual programme quickly. These buttons can be
re-programmed to select your favourite wash programmes instead of the
pre-set ones.

c

Start button

d

PC / Optical interface

This is used by service technicians for testing purposes and for uploading new
software to the machine.

e

Multi-function selector

This is used to select menu options (by turning it) and to confirm your selection
(by pressing it).

f

On-Off button

s

Before using for the first time

Before using the machine for the first time ensure that it is correctly installed
and connected. See "Installation". Also check that the drain filter is securely
tightened to prevent the risk of water leaks during use.

Commission the appliance as described in the separate booklet
"

Commissioning, Programme chart and Settings

" supplied

Operating the machine

14

Summary of Contents for PW 6080 VARIO

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands