manualshive.com logo in svg

Miele PW 6065 Vario, Operating And Installation Instructions

Share
Download
Miele PW 6065 Vario Operating And Installation Instructions Download Page 29

The timer can be used to select the time you want the pro-
gramme to finish. The start of a programme can be delayed
from 30 minutes up to a maximum of 24 hours,

To open the Timer sub-menu

Cottons Uni.

60°C

1400 rpm

Duration 0:47 h

Extras

H

Timer

Y

H

Back

A

H

^

Press short cut button

E

below the word Timer. This

opens the

Timer

sub-menu.

To select a delay start time

You can enter the finish time for a programme in 30 minute
stages.

Cottons Uni.

60°C

1400 rpm

10:03

Start time:

10:38

Finish:

11:30

^

Use the multi-function selector to select the programme
finish time and confirm your selection.
The programme finish time will be adjusted to the next full
or half hour.
The start of the programme will now be delayed in parallel
with the programme finish time you have selected.

To start the timer

^

Press the

Start

button.

The delay start time will be shown counting down in minutes.

To cancel the timer

^

Press short cut button

G

.

The actual load size can only be determined accurately by
the machine once the programme has started. This can
cause the finish time for the programme to vary.

Timer

29

Summary of Contents for PW 6065 Vario

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands