Miele PW 5065 Operating Manual Download Page 62

Page: 62 / 64

MINIMUM IRON duration

The program "MINIMUM IRON"
allows you to extend the wash time
for the main wash.

The machine comes factory set with the
option Block Parameter selected. (The
wash time will be controlled according
to the factory set program data.)

Special programs list

Special programs can be added to
the program selection.

Option 1: The programs Quick wash,
Shirts, Starch, Pillows, Outerwear and
Proofing are shown. (Factory set)

Option 2: In addition to option 1
"Intensive wash" is offered.

Option 3: In addition to option 1 "Flour",
"Flour +" and "Grease and fat" are
offered.

Option 4: In addition to option 1
"Grease and fat" and "Grease and fat +"
are offered.

Option 5: In addition to option 1 "Towels
short", "" and "Capes" are
offered.

Option 6: In addition to option 1 "Chem.
Therm. Dis." (Chemothermal
Disinfection 20 minutes 60°C) is
offered.

Hygiene

If a temperature lower than 140°F
(60°C) was selected for the last
wash program "Hygiene" is
displayed.

The machine comes factory set with
this option "off".

Pre-wash

For the programs "COTTONS" and
"MINIMUM IRON" pre-wash can be
permanently added.

If the pre-wash is permanently
selected, the indicator of the pre-wash
button lights.

The machine comes factory set with the
option "Menu selection" activated.

COTTONS rinses

The program "COTTONS" allows you
to change the number of rinses.

2 rinses (factory set)
3 rinses
4 rinses
5 rinses

Menu Settings - Supervisor level

Summary of Contents for PW 5065

































































Search results

Summary of Contents for PW 5065

Reviews:

Related manuals for PW 5065

Brands by name

Popular brands

Miele PW 5065, Operating Manual

Search results

Summary of Contents for PW 5065

Reviews:

Related manuals for PW 5065

Brands by name

Popular brands