Miele PT 7136 Vario OS Operating And Installation Instructions Download Page 39

Page: 39 / 56

Problem

Possible cause

Remedy

The programme
does not start and
the display is dark.

There is no power to
the dryer.

– Is the dryer switched on?

– Is the door closed properly?

– Has the fuse or circuit

breaker tripped?

When the power comes back
on after a power cut, confirm
with

and start the

programme again.

The dryer switches off
automatically after 15
minutes if no further
selection is made.

Switch the dryer on.

The display is dark
and the

Start

button

is flashing slowly.

The display has
switched off
automatically to save
energy: Standby.

The display and the
multi-function selector will light
up when one of the buttons is
pressed.

The display is in a
different language.

A different language
has been selected.

Set the language you want. The

flag symbol

will guide you.

The

Start

button

light flashes when a
programme is being
selected.

The flashing indicates
that a programme can
be started.

Once the programme has been
started, the

Start

button stops

flashing and lights up
constantly.

The interior drum
lighting does not
come on.

The lighting switches
off automatically (to
save energy).

– It will switch on again after

the door has been closed
and then opened.

– If the lamp needs to be

replaced, follow the
instructions in "Changing the
lamp" at the end of this
section.

Problem solving guide

Summary of Contents for PT 7136 Vario OS

























































Search results

Summary of Contents for PT 7136 Vario OS

Reviews:

Related manuals for PT 7136 Vario OS

Brands by name

Popular brands

Miele PT 7136 Vario OS, Operating And Installation Instructions

Search results

Summary of Contents for PT 7136 Vario OS

Reviews:

Related manuals for PT 7136 Vario OS

Brands by name

Popular brands