Miele PDR 908 HP Operating And Installation Instructions Download Page 87

Page: 87 / 108

Supervisor level

Opening the supervisor level



11:02







Programs

Favorites

Supervisor

Help

Touching the



sensor control takes

you to the supervisor level.

Access via code

The supervisor level is accessed using
a code.

Factory default: The code is

000

Change code

You can alter the supervisor-level
access code to protect the tumble
dryer from unauthorized access.

Carefully enter a new code.
Please inform Technical Service if
you have forgotten your new code.
Technical Service will have to reset
the code.
Make a note of your new code and
store it in a safe place.

Closing the settings menu



Touch the



sensor control.

The display will then go back to the
previous menu level.



Touch the



sensor control.

The display will change to the main
menu.

Controls / Display

Language

The display can be set to appear in
one of several different languages. To
select the language you want, go to
the

Languages

sub-menu.

You can change the language as
follows:

– Permanently using the supervisor

level (= “Supervisor language”).

– For the duration of the current

program only using the



sensor

control. The supervisor language is
displayed again at the end of the
program.

Summary of Contents for PDR 908 HP













































































































Search results

Summary of Contents for PDR 908 HP

Reviews:

Related manuals for PDR 908 HP

Brands by name

Popular brands

Miele PDR 908 HP, Operating And Installation Instructions

Search results

Summary of Contents for PDR 908 HP

Reviews:

Related manuals for PDR 908 HP

Brands by name

Popular brands