background image

Program chart

Delicates

Maximum 8.8 lb (4 kg)*

Normal Plus, Normal, Hand iron plus

Items

– Delicate synthetic, cotton ,or mixed-fiber fabrics.

– Lightweight pullovers, dresses, pants, overalls, table cloths, dress

shirts, and blouses.

– Lingerie and appliquéd fabrics.

Note

Less creasing occurs in this program.

Tip

Reducing the load will reduce creasing even further.

Dress Shirts

Maximum 4.4 lb (2 kg)*

Normal, Hand iron plus

Items

Shirts and blouses.

Denim

Maximum 7.7 lb (3.5 kg)*

Normal, Hand iron plus

Items

Denim garments, e.g., jeans, jackets, skirts, shirts.

Woolens

Maximum 4.4 lb (2 kg)*

Items

Woolen garments and fabric containing wool blends, e.g., pullovers,
cardigans, tights.

Note

– Wool and wool-blend items are only fluffed up; they are not dried

completely.

– Remove garments as soon as the program has finished and leave

to finish drying at room temperature.

Silks

Maximum 2.2 lb (1 kg)*

Items

Silk garments which are suitable for tumble drying, e.g., blouses and
shirts

Note

– Program for reduced creasing.

– Items are not dried completely in this program.

– Remove the garments as soon as the program has finished.

36

Summary of Contents for PDR 908 HP













































































































Reviews: