Miele Paramount Operating Instructions Manual Download Page 15 | Manualshive

Page: 15 / 72

background image

B

Switch on the washing machine

C

Load the drum

^

Press the

Door

button to open the

drum door.

^

Unfold the laundry and load loosely
in the drum. Mixing both large and
small items gives better wash results
and also helps distribute the load
evenly during spinning.

The most efficient use of energy and
water is achieved when a full load is
washed. However, do not overload as
this causes creases and reduces
cleaning efficiency.

Make sure that no garments are
caught between the drum door and
seal.

^

Shut the door with a gentle swing.

D

Select a programme

^

Turn the programme selector
clockwise or anti-clockwise to the
required programme. The
programme indicator light for the
programme selected will come on.

E

Select a temperature / spin speed

The suggested temperature and/or spin
speed can be changed.

1:49

60°

1400

^

Press the

Temperature

button to alter

the temperature and press the

Spin

speed

button to alter the spin speed.

How to wash correctly

15

«
...
13
14
15
16
17
...
»

Summary of Contents for Paramount









































































Reviews:

No comments

Related manuals for Paramount

Brand: GE Pages: 11

Brand: Kärcher Pages: 24

Brand: Asko Pages: 32

Brand: NEFF Pages: 48

Brand: Zanussi Electrolux Pages: 20

Brand: Kärcher Pages: 368

FAVORIT 88015 VI

Brand: AEG Electrolux Pages: 36

Brand: Zanussi Electrolux Pages: 28

Brand: Saba Pages: 47

Brand: Simoniz Pages: 10

ProWash P1000 HOT

Brand: Target Pages: 26

HG6085C13J7609DW

Brand: Hanseatic Pages: 76

Brand: Briggs & Stratton Pages: 2

Brand: Miele professional Pages: 140

Brand: Samsung Pages: 220

Brand: Electrolux Pages: 24

Brand: Electrolux Pages: 26

Brand: Electrolux Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands