Miele G 8050 Operating Instructions Manual Download Page 68 | Manualshive

Page: 68 / 76

background image

The G 8050 / PG 8050i comes
equipped with a 14/3 AWG cord and
plug for connection to a standard 120
V, 60 Hz AC power outlet.

If available, the dishwasher may be
connected to a 208/240V single phase
power supply. This will increase the
power to the heating elements and
shorten the time of selected wash
cycle.

120V 208V 240V

Rated Load (kW) 1.5

3.6

4.0

Fuse Rating

15A

20A

20A

To connect the machine to a 208/240V
supply, the standard power cord must
be removed and replaced by a 10/4
AWG SJ or SJO cable. A 3 pole, 4-wire
grounding plug and receptacle are
recommended (NEMA Type 14-20R
and 14-20P).

The

conversion diagram

and

wiring

diagram

are secured to the inner side

of the toe kick.

Removing the toe kick

Disconnect the machine from the
mains electrical supply.

^

Remove the fixing screws from the
toe kick and take it off.

Power connection options

Electrical connection

68

«
...
66
67
68
69
70
...
»

Summary of Contents for G 8050













































































Reviews:

No comments

Related manuals for G 8050

Brand: Maidaid Halcyon Pages: 17

Brand: NEFF Pages: 52

Brand: Candy Pages: 136

Brand: Candy Pages: 41

Brand: Indesit Pages: 72

Brand: Bush Pages: 44

Appliances Profile PFWS4605

Brand: GE Pages: 88

Brand: Fisher & Paykel Pages: 12

Brand: GE Pages: 12

Brand: Iberna Pages: 24

Brand: Maytag Pages: 36

Brand: Küppersbusch Pages: 28

Brand: FAR Pages: 16

Brand: Acorn Safety Pages: 6

Brand: Sandstrom Pages: 36

Brand: VALBERG Pages: 108

Brand: VALBERG Pages: 128

Brand: Caple Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands