Miele G 7856 Operating And Installation Instructions Download Page 31 | Manualshive

Page: 31 / 56

background image

3. Selecting an economy interim
rinse (only for "Rapid" program)

^

Turn the program selector to "Stop".

^

Turn the machine off.

^

Press and hold the "Display" and
"Start" buttons,

at the same time

turn

the machine on with the "On/Off"
button.
The display shows the current
program status "P...".
The "Fill/Drain" indicator lights.

^

Press the "Extra Drying" button once.
"E01" (programming level 1) is
displayed.

^

Turn the program selector to "Rinse".
"40" or "41" is displayed.
"40" = without economy interim rinse
"41" = with economy interim rinse

^

Press "Display" to change from "40" to
"41" or vice versa.

^

Press the "Start" button. "SP" is
displayed.

^

Press the "Start" button again. The
change has been saved.

Value set:

4. Venting and setting the dosage for
liquid cleaning agents (optional
extra)

^

Turn the program selector to "Stop".

^

Turn the machine off.

^

Press and hold the "Display" and
"Start" buttons,

at the same time

turn

the machine on with the "On/Off"
button.
The display shows the current
program status "P...".
The "Fill/Drain" indicator lights.

^

Press "Extra Drying" twice. "E02"
(programming level 2) is displayed.

Venting the dispensing system:

^

Turn the program selector to "Rinse".
"do1" is displayed.

^

Press "Display" for 90 secs.
The dosage system is vented.

If only

venting

is required:

^

Turn the machine off with

On/Off

(I-0)

button.

Immediately:

Start the "Rinse" program,

so that after venting any agents in the
wash cabinet are diluted before being
drained away.

Programming special functions

31

«
...
29
30
31
32
33
...
»

Summary of Contents for G 7856

























































Reviews:

No comments

Related manuals for G 7856

Brand: Gaggenau Pages: 48

Brand: Gaggenau Pages: 48

Brand: Gaggenau Pages: 40

Brand: Gaggenau Pages: 68

Brand: Jackson Pages: 80

Brand: Jackson MSC Pages: 42

Brand: Hoover Pages: 17

Brand: Indesit Pages: 72

Brand: Danby Pages: 44

Brand: Indesit Pages: 60

Brand: Hanseatic Pages: 100

Brand: Hotpoint Pages: 16

Brand: ZANKER Pages: 52

Brand: Progress Pages: 48

Brand: lamber Pages: 32

Brand: BENDIX Pages: 20

Speed Queen AWM190

Brand: Raytheon Pages: 86

Brand: Bosch Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands