background image

Service

107

Contact in case of malfunction

In the event of any faults which you
cannot remedy yourself, please contact
your Miele dealer.

Contact details for your Miele dealer
are given at the end of this document.

Please note that telephone calls may be
monitored and recorded for training
purposes and that a call-out charge will
be applied to service visits where the
problem could have been resolved as
described in this booklet.

Please quote the model and serial
number of your appliance when
contacting your Miele dealer. This
information can be found on the data
plate.

The data plate is located on the right
side of the door.

EPREL database

From 1 March 2021, information on
energy labelling and ecodesign
requirements will be available in the
European Product Database (EPREL).
You can find the product database at
the following link https://
eprel.ec.europa.eu/. Y
ou will be asked
to enter the model identifier.

The model identifier can be found on
the data plate.

X xxxx

Miele & Cie. KG, Carl-Miele-Straße 29

33332 Gütersloh, Germany

Made in xxxx

Mod:

Type:

XX/XXXXXXXXX

HGXX

M.No: XXXXXXXX

AC xxx  V x Hz

xx A

x,x kW

Guarantee

For information on the appliance
guarantee specific to your country
please contact your Miele dealer. See
end of this booklet for contact details.

Summary of Contents for G 7110

























































































































Reviews: