background image

www.acornsafety.com

 

 

INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS

 

 

 

WALL MOUNT SHROUDED EYE/FACE WASHES

 

TECHNICAL ASSISTANCE TOLL FREE TELEPHONE NUMBER

1.800.591.9360

TECHNICAL ASSISTANCE FAX: 1.626.855.4894

ACORN SAFETY

P.O. BOX 3527
CITY OF INDUSTRY, CA 91744-0527

UNITED STATES OF AMERICA

 

Models S0470 / S0470-BF / S0480 / S0480-BF

Manual #7109-103-001

Revised: 05/06/13

NOTES TO THE INSTALLER:

1. Please leave this documentation with the owner of the fixture when finished.

2. Please read this entire booklet before beginning the installation.

3. Check your installation for compliance with plumbing, electrical, ANSI Z358.1 and 

other applicable codes.

LIMITED WARRANTY

UNITED STATES AND CANADA

Acorn Safety warrants that its products are free from defects in material or workmanship under normal use and 
service for a period of one year from date of shipment or 18 months after the date of shipment from factory , 
whichever comes first. Acorn's

 liability under this warranty shall be discharged solely by replacement of repair of 

defective material, provided Acorn

 is notified in writing within one year from date of shipment, F.O.B. Industry, 

California.

This warranty does not cover installation or labor charges and does not apply to materials, which have been 
damaged by other causes such as mishandling or improper care or abnormal use. The repair or replacement of the 
defective materials shall constitute the sole remedy of the Buyer and the sole remedy of Acorn

 under this warranty. 

Acorn

 shall not be liable under any circumstances for incidental, consequential or direct charges caused by defects 

in materials, or any delay in the repair or replacement thereof. This warranty is in lieu of all other warranties 
expressed or implied. Product maintenance instructions are issued with each unit and disregard or non-compliance 
with these instructions will constitute an abnormal use condition and void the warranty. Stainless steel must be 
protected on job sites during construction and must be properly maintained after the water has been introduced into 
the safety product or Acorn's

 warranty is void.

 

Acorn Safety

 

a division of Acorn Engineering 

Company

Summary of Contents for S0470







Reviews: