Miele G 691 Operating Instructions Manual Download Page 34

Page: 34 / 68

Switching on

Make sure the spray arms are not ob-
structed.

Close the door.

Open the stopcock, if it is closed.

Press the “On/Off” button (16).

All indicator lights (17) next to the pro-
gramme buttons and the decimal point
in the time display (19) light up.

Starting a programme

When selecting a programme, refer
to the programme chart at the end of
the operating instructions.

Press button (17) for the required pro-
gramme.

All indicator lights next to the pro-
gramme buttons, except the one for the
programme selected, go out.
The indicator light next the the “Start/
Stop” button comes on.

The running time of the programme se-
lected appears in the time display (19)
in hours and minutes.
The “Time Left” indicator light comes
on.

Note:

If selecting “Delay start” or “Top Solo”
this must be done before the pro-
gramme is started (see “Additional
functions” ).

Press the “Start/Stop” button (22).

The indicator light next to the
“Start/Stop” button goes out. The pro-
gramme cycle commences.

Do not finish a programme prema-
turely.
Important programme stages (e. g.
reactivating the water softener)
could be omitted.

Programme sequence indica-
tor lights (15)

After a programme has been started
the current stage of the programme is
indicated by the programme sequence
indicator lights (15).

Operating the dishwasher

Summary of Contents for G 691





































































Search results

Summary of Contents for G 691

Reviews:

Brands by name

Popular brands

Miele G 691, Operating Instructions Manual

Search results

Summary of Contents for G 691

Reviews:

Brands by name

Popular brands