Miele G 4970 Operating Instructions Manual Download Page 44

Page: 44 / 76

Options

Factory default settings

If you have altered any settings from
the factory default, you can reset them
back to the factory default settings as
follows:

Open the door.

Turn the dishwasher off with the

button, if it is turned on.

Press the program selection button

, and,

simultaneously

switch the

dishwasher on using the

button.

Keep the program selection button

pressed in for at least four seconds
until the lower right program indicator
light comes on.

If this does not happen, start the proce‐
dure from the beginning again.

Press the

button 19 times.

The

indicator light will flash once at

a long interval and then 9 times at short
intervals.

The flashing sequence in the display in‐
dicates whether a setting has been
changed from its factory default.

–

ɠɇ

: All settings are set to factory de‐

fault settings

–

ɠɆ

: At least one setting has been

changed

To reset the dishwasher to the factory
default settings, press the program
selection button

The setting is now stored in memory.

Turn the dishwasher off with the

button.

Summary of Contents for G 4970













































































Search results

Summary of Contents for G 4970

Reviews:

Related manuals for G 4970

Brands by name

Popular brands

Miele G 4970, Operating Instructions Manual

Search results

Summary of Contents for G 4970

Reviews:

Related manuals for G 4970

Brands by name

Popular brands