Miele G 4170 SCVI Operating Instructions Manual Download Page 43

Page: 43 / 64

Water inlet/drain fault

Problem

Possible cause

Remedy

The dishwasher
stops working
shortly after the start
of the programme.
The buzzer sounds.
The Inlet/drain check
light

flashes

when the door is
opened.

The stopcock is
closed.

– Open the stopcock fully.

The dishwasher
stops during a
programme.
The buzzer sounds.
The Inlet/drain check
light

flashes

when the door is
opened.

Before rectifying the problem:

– Switch the dishwasher off with the

Off button

Water intake is
restricted.

– Open the stopcock fully.

– Clean the water inlet filter (see

"Maintenance").

– The water pressure at the intake is

lower than 30 kPa (0.3 bar).
Seek professional advice.

The water outlet is
restricted, water
remains in the
wash cabinet at
the end of a
programme.

– Clean the filter combination. See

"Cleaning and care".

– Clean the drain pump. See

"Maintenance".

– Clean the non-return valve. See

"Maintenance".

– Remove any kink in the drain

hose.

Problem solving guide

Summary of Contents for G 4170 SCVI

































































Search results

Summary of Contents for G 4170 SCVI

Reviews:

Related manuals for G 4170 SCVI

Brands by name

Popular brands

Miele G 4170 SCVI, Operating Instructions Manual

Search results

Summary of Contents for G 4170 SCVI

Reviews:

Related manuals for G 4170 SCVI

Brands by name

Popular brands