Miele G 1672 Operating Instructions Manual Download Page 51

Page: 51 / 84

Problem

Possible cause

Remedy

The In-operation
indicator is flashing
quickly. In the
"Without heater"
programme the
following message
appears:

Water intake temp. too
low

The intake water has
not reached the
required temperature of
45°C (see "Connection
to the water supply").

– Start the programme again.

– If the fault message

appears again, select a
different programme.

The In-operation
indicator is flashing
quickly.
The buzzer is
sounding.
The following
message appears in
the display:

Drain fault F11

Before rectifying the problem
you must:

– Switch the dishwasher off

with the Off button

Water outlet is
restricted, water
remains in the wash
cabinet at the end of a
programme.

– Clean the filter

combination. See Cleaning
and care.

– Clean the drain pump. See

Maintenance).

– Clean the non-return valve.

See Maintenance).

– Remove any kink in the

drain hose.

Problem solving guide

Summary of Contents for G 1672





















































































Search results

Summary of Contents for G 1672

Reviews:

Related manuals for G 1672

Brands by name

Popular brands

Miele G 1672, Operating Instructions Manual

Search results

Summary of Contents for G 1672

Reviews:

Related manuals for G 1672

Brands by name

Popular brands