background image

General problems

Problem

Possible cause

Remedy

Detergent residue is
left in the dispenser at
the end of a
programme.

The dispenser was still
damp when detergent was
added.

Make sure the dispenser is
dry before adding
detergent.

The detergent
dispenser lid cannot
be closed properly.

Clogged detergent residue
is blocking the catch.

Clean the detergent from
the catch.

At the end of a
programme there is a
film of moisture on
the inside of the door
and the interior walls.

This is caused by the
drying system and does not
indicate a fault.

The moisture will dissipate
after a short while.

Water remains in the
wash cabinet at the
end of a programme.

Before rectifying the
problem you must:

– Switch the dishwasher

off with the Off button

V

.

The filter combination in the
wash cabinet is clogged.

Clean the filter
combination. See
"Cleaning and care".

The drain pump or
non-return valve may be
blocked.

Clean the drain pump or
the non-return valve. See
"Maintenance".

The drain hose is kinked.

Remove any kink from the
drain hose.

Problem solving guide

44

Summary of Contents for G 1162 SCVi

































































Reviews: