Miele for dishwashers Page 43 Operating Instructions Manual Download

Page: 43 / 76

Cleaning the spray arms

Particles of food can get stuck in the
spray arm jets and bearings. The spray
arms should therefore be inspected
and cleaned regularly (approx. every
4 - 6 months).

Switch the dishwasher off.

Remove the spray arms as follows:

Take out the cutlery tray (if your
dishwasher is fitted with one).

Push the

top

spray arm upwards to

engage the inner ratchet. Then
unscrew the spray arm.

Push the

middle

spray arm upwards

to engage the ratchet. Then

unscrew the spray arm

Remove the lower basket.

Pull the

lower

spray arm firmly

upwards to remove it.

Use a pointed object to push food
particles into the spray arm jets.

Rinse thoroughly under running
water.

Replace the spray arms and check
that they rotate freely.

Cleaning and care

Summary of Contents for for dishwashers













































































Search results

Summary of Contents for for dishwashers

Reviews:

Related manuals for for dishwashers

Brands by name

Popular brands

Miele for dishwashers, Operating Instructions Manual

Search results

Summary of Contents for for dishwashers

Reviews:

Related manuals for for dishwashers

Brands by name

Popular brands