Miele F 1811 Vi Operating And Installation Manual Download Page 47

Page: 47 / 80

Have the appliance installed by a
qualified technician, according to
the enclosed installation instructions.

WARNING
This appliance is top-heavy and
must be secured to prevent it from
tipping forward.
Keep the door closed until the
appliance is completely installed
and secured as per the installation
instructions.

Empty weight of your machine:

F 18X1 Vi

. . . . . . . . . . 421 lbs (191 kg)

F 19X1 Vi

. . . . . . . . . . 459 lbs (208 kg)

Installation site

The appliance should be installed in a
dry, well-ventilated room.

Do not install the appliance:
- outdoors
- in an environment with dripping

water

- in rooms that are at risk of frost.

The installation location should not be
exposed to direct sunlight, nor near a
heat source, such as an oven,
radiator, etc.

The ambient temperature should not
drop below 55°F (13°C) or rise above
110°F (43°C), otherwise malfunctions
may occur.

If installation next to a heat source is
unavoidable observe the following
minimum distances from the heat
source:

– 1

" (3 cm) from an electric cooktop

or electric oven.

– 12" (30 cm) from a gas or oil

cooktop, range or oven.

Installation

Summary of Contents for F 1811 Vi

















































































Search results

Summary of Contents for F 1811 Vi

Reviews:

Related manuals for F 1811 Vi

Brands by name

Popular brands

Miele F 1811 Vi, Operating And Installation Manual

Search results

Summary of Contents for F 1811 Vi

Reviews:

Related manuals for F 1811 Vi

Brands by name

Popular brands