Miele DA 3668 Operating And Installation Instructions Download Page 21

Page: 21 / 72

Before using for the first time

Sign out of WiFi (reset to factory
settings)

To set up a new WiFi connection, the
existing WiFi connection must be
disconnected.



Switch the cooker hood off.



Press and hold the



control.



Touch the lighting control at the same
time



With an existing WiFi connection the

and the

will light up constantly.

The cooker hood is ready for
disconnection in the next two minutes.



Touch the



control.

will light up constantly,

will flash on

and off.

After a few seconds the

and the

will

flash on and off. The connection has
now been disconnected.



Quit disconnection mode on the
cooker hood by pressing the Run-on
control



The WiFi connection has now been
disconnected. A new connection can
now be set up.

Summary of Contents for DA 3668









































































Search results

Summary of Contents for DA 3668

Reviews:

Related manuals for DA 3668

Brands by name

Popular brands

Miele DA 3668, Operating And Installation Instructions

Search results

Summary of Contents for DA 3668

Reviews:

Related manuals for DA 3668

Brands by name

Popular brands