manualshive.com logo in svg

Miele DA 3566, Operating And Installation Instructions

Share
Download
Miele DA 3566 Operating And Installation Instructions Download Page 46

Installation

46

dai2699

Attach the exhaust ducting, e.g. flexi‐

ble hose, to the exhaust socket using

a hose clip (available as an optional

accessory). When using 

 125 mm

ducting, fit the reducing collar sup‐

plied into the exhaust socket (see

"Connection for air extraction").

Attach the exhaust ducting to the ex‐

haust socket on the cooker hood.

See "Connection for air extraction"

for further instructions on fitting the

ducting.

Setting up for recirculation

mode

If site conditions are not suitable for the

cooker hood to be used with air extrac‐

tion, the appliance must be set up for

recirculation. A conversion kit, available

through your dealer of from Miele is re‐

quired for operating the cooker hood in

recirculation mode. You will also need

two charcoal filters (see "Technical da‐

ta").

Conversion kit DUU 150 with a plastic

grille is suitable for fitting in a non-visi‐

ble area at the top of the wall unit.

Conversion kit DUU 151 with a stain‐

less steel grille is recommended if the

grille is to be fitted in an area which is

visible.

Fit the conversion kit as described in

the installation instructions supplied

with the kit. Make sure that the slats

in the exhaust grille point towards the

centre of the room and not towards a

Summary of Contents for DA 3566

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands