manualshive.com logo in svg

Miele DA 3566, Operating And Installation Instructions

Share
Download
Miele DA 3566 Operating And Installation Instructions Download Page 31

After Sales / Guarantee

31

In the event of a fault which you cannot

remedy yourself, please contact your

Miele dealer or the Miele Service De‐

partment.
Contact details for Miele are given at

the back of this manual. N.B. A call-out

charge will be applied to service visits

where the problem could have been re‐

solved as described in these instruc‐

tions.
When contacting your dealer or Miele,

please quote the model and serial num‐

ber of your appliance.

These are shown on the data plate.

Position of the data plate

The data plate is located on the casing

of the cooker hood and is visible when

the cover for the charcoal filter slots is

removed.

Guarantee: U.K.

In the U.K., the appliance is guaranteed

for 2 years from the date of purchase.

However, you must activate your cover

by calling 0330 160 6640 or registering

online at www.miele.co.uk.

Guarantee: Other countries

For information on the appliance guar‐

antee specific to your country please

contact Miele. See end of this booklet

for contact details.

Summary of Contents for DA 3566

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands